How To Change Oil And Air Filter On Craftsman Ys4500 Manual

SERVICE REMINDER/60 minutes METER

Service reminder shows the total number

of hours the engine has run and flashes to

indicate that the engine or mower needs

servicing. When service is required, the

service reminder wilt flash for two hours.

To service engine and mower, meet the

Maintenance section of this manual.

Notation: Service reminder runs when the igni-

tion central is in any position just "End". For

accurate reading, exist sure key remains inthe

"Stop" position when engine is not running.

Before STARTING THE ENGINE

Bank check ENGINE OiL LEVEL

The engine in your tractor has been

shipped, from the factory, already filled

with summer weight oil.

1. Cheque engine oil with tractor on level

ground.

ii. Unthread and remove oil make full cap/dip-

stick; wipe oil off. Reinsert the dipstick

into the tube and rest oil fill cap on the

tube. Do not thread the cap onto the

tube. Remove and read oil level. If

necessary, add oil until "FULL' mark

on dipstick is reached. Do non overfill.

• For cold weather condition performance you should

modify oil for easier starting (Run across the

oil viscosity chart in the Maintenance

section of this manual).

• To change engine oil, run across the Mainte-

nance department in this manual.

Add GASOLINE

• Fill up fuel tank to bottom of filler neck. Do non

overfill. Usefresh, clean, regutarunleaded

gasoline with a minimum of 87 octane.

(Utilise of leaded gasoline will increase

carbon and leadoxide deposits and reduce

valve life). Do not mix oil with gasoline.

Purchase fuel inquantities that tin can be used

within 30 days to assure fuel freshness.

_,Caution: Wipe off any spilled oil or

fuel. Practise not store, spill or use gasoline

near an open up flame.

important: When operating in temper-

atures betow32°F(0°C), use fresh, clean

winter grade gasoline to help insure good

cold weather condition starting.

CAUTION: Alcohol blended fuels (chosen

gasohol or using ethanol or methanol) can

attract moisture which leads to separation

and formation of acids during storage.

Acidic gas can damage the fuel system

of an engine while in storage. To avoid

engine problems, the fuel system should

be emptied earlier storage of 30 days

or longer. Drain the gas tank, get-go the

engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage instructions for

additional data. Never use engine

or carburetor cleaner products inthe fuel

tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first fourth dimension

or if the engine has run out of fuel, it will

take extra cranking time to move fuel from

the tank to the engine.

1. Be certain freewheel control isin the

transmission engaged position.

2. Sit on seat inoperating position, depress

brake pedal and set parking brake.

3. Motility attachment clutch to disengaged

position.

4. Motility throttle control to fast position

v. Pullchokecontrotoutforacotd enginestart

attempt. For awarm engine start attempt

the choke command may not be needed.

Note: Before starting, read the warm and

common cold starting procedures below.

six. insert key into ignition and turn fundamental

clockwise to start position and release

central as presently equally engine starts. Do not run

starter continuously for more than 15

seconds per infinitesimal. If the engine does

non outset afterward several attempts, push

asphyxiate control in, wait a few minutes

and try once again. If engine still does not

beginning, putt the asphyxiate control out and retry.

WARM WEATHER STARTING (50° F and

to a higher place)

7. When engine starts, slowly push choke

control in until the engine begins to

run smoothly, if the engine starts to

run roughly, pull the choke command out

slightly for a few seconds and so

continue to button the command in slowly.

• The attachments and ground drive can

now be used. if the engine does not

accept the load, restart the engine and

allow itto warm upwards for one minute using

the asphyxiate equally described above.

COLD Conditions STARTING (50° F and

below)

8. When engine starts, slowly push choke

control in until the engine begins to run

smoothly. Proceed to push the choke

control in small steps assuasive the en-

gine to accept modest changes in speed

and load, until the choke command isfully

in. If the engine starts to run roughly,

pull the choke control out slightly for a

few seconds and then go on to push

the command in slowly. This may require

an engine warm-up flow from several

seconds to several minutes, depending

17 on the temperature.

How To Change Oil And Air Filter On Craftsman Ys4500 Manual,

Source: http://lawnandgarden.manualsonline.com/manuals/mfg/craftsman/yt_4500.html?p=17

Posted by: hunsuckermilitaidele1997.blogspot.com

Share this post